STORES: LAWNTON (07) 3889 8898 & CAPALABA (07) 3823 5366
OPENING HOURS: 8:30am-5pm Mon to Fri, 8:30am-1pm Sat
SEARCH:

BRAKE CONTROLLER TEKONSHA PRODIGY P2

Description

Proportional Braking

With a proportional brake controller, you can get heavy-duty emergency braking, general braking or slow-to-an-idle braking for your trailer automatically. The intensity with which your trailer brakes are activated and the rate at which they are applied are dependent on the deceleration of your tow vehicle. This means that, unlike time-delay controllers - which send the same amount of preset power to your trailer brakes every time - proportional controllers are able to adapt to every braking situation differently. So, if you slam on the brakes in your truck, your trailer brakes will activate with that same extreme intensity. And if you merely slow down as you approach a red light, your trailer will gradually brake in the same manner. Just set the initial power level, select a boost setting, and you're good to go.


As long as the P2 controller sits level on a horizontal plane and is pointed in the direction of travel, it will sense - via an internal inertia sensor - how your tow vehicle brakes. This inertia-based sensor responds to the deceleration of your tow vehicle as you brake by signaling the controller to send out enough power to your trailer brakes so that they are activated with an intensity that matches. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.

 

Power Boost for Heavy-Duty Towing

Aside from smoother, more efficient braking, Tekonsha's P2 brake controller also offers a boost feature that gives you more initial braking power for those times when you're towing heavy loads. You can switch boost levels so that the power output to your trailer brakes automatically starts out at either 14 percent or 28 percent of the predetermined power setting.


So, if you boost the initial power so that your trailer brakes activate with 28 percent of the overall intensity at the start, the brakes will reach maximum braking faster. This is particularly beneficial if you are towing a heavy load because the intensity required to stop that load may be far greater than that needed to halt your vehicle. Therefore, sending out more initial power to the trailer brakes - and causing them to reach maximum braking faster - allows you to better control the trailer so that it doesn't push your tow vehicle before coming to a complete stop.


If your trailer weighs less than your tow vehicle, no boost is needed. But if you wish to set the boost so that your trailer leads the braking of your towing setup, you can select level B1. The following table gives an indication of when you might use the different boost levels and the power increases that they offer.

 

Automatic Leveling and Simple Installation

The self-leveling feature of the P2 ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at any vertical angle, and the controller will level itself automatically thanks to its 360-degree rotational range.


 

 

Safety Features

The Prodigy P2 offers advanced safety features to prevent damage to various components of your towing setup. Integrated reverse battery protection shields the brake controller and your trailer's breakaway system from shorts. When the P2 is not in use, it will be in power-saving mode. In this setting, the power draw falls to only 3.6 milliamps, minimizing drain on your vehicle's battery.


When you stop at red lights, or any time that your truck and trailer are at a standstill with the brakes applied for more than 5 seconds, the P2's "hold" feature will activate. When this happens, the power output to your trailer's brakes will be reduced to just 25 percent of the preset power setting so that the brakes will not overheat.


If ever there is a time that you need to brake your trailer separately from your tow vehicle - when traveling down a steep incline, for example - the manual override lever is easily accessible. Pushing this lever engages the brakes on your trailer with full power. In addition, when you activate this override, the brake lights on your trailer will illuminate, properly warning those behind you of the braking action of your rig.


In addition to all of those safety features listed above, the P2 offers diagnostics such as:

  • Open ground
  • Overload
  • Output short
  • Power loss
  • No trailer connection

 

 

Prodigy P2

 

Things You Need To Know!

Features & Benefits:

Reverse battery protection for both vehicle and breakaway
Designed to work with electronic over hydraulic brake systems
Numerous mounting options - including 360 degree vertical rotation
Digital display depicts voltage delivery to trailer during braking
No level adjustment necessary - it adjusts itself to varying terrain as you drive
Great for backing into tough spots! Works proportionally in reverse with the ability to disable when not needed
Produces stops that are in proportion to vehicles deceleration rate
"Boost" feature gives users the ability to apply more initial trailer braking power when towing heavier trailers
Continual diagnostics check for proper connection, shorted magnet conditions and much more
Quick and easy disconnect feature allows user to remove and store the control when not in use
Electric trailer brake control for up to 4 braking axles
Limited lifetime warranty
Product ID:
1803
Price:
$195.00
Qty: 
go back
OUR PARTNERS
CEC Approved Retailer trinasolar sma Enphase Enphase Fronius LG Tesla
facebook youtube share with email LinkedIn
© SPRINGERS SOLAR 2017
ABN 63 086 620 644