BTEC LIFEPO4 24V 100AH DC-DC BUNDLE

BTEC LIFEPO4 24V 100AH DC-DC BUNDLE

EPL100BT 24V ENERDRIVE LITHIUM IRON PHOSPHATE (LIFEPO4) BATTERY • EN3DC30-24V EPOWER DC-DC CHARGER • BUILT IN BLUETOOTH MONITORING


Brand: Enerdrive

Reference No. K10024VDCBUNDLE

0

3,799.00Incl

3,453.64Excl
Add to Cart

**BUNDLE CONSISTS OF 100AH BTEC LITHIUM BATTERY & EN3DC30-24V EPOWER DC-DC CHARGER**


ePOWER B-TEC LiFeP04 24v 100Ah Lithium Battery


Available in 12v 100Ah, 125Ah, 200Ah capacities and 24v & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.


Smart Phone Monitoring System


The Enerdrive ePOWER B-TEC battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information;


  • Battery Capacity

  • Battery Voltage

  • Battery Current (Amps)

  • Battery State of Charge (SOC)

  • Battery State of Health (SOH)

  • Battery Status

  • Individual Cell Voltage

  • Battery Temperature

  • Battery Cycles

  • Battery Alarms

  • Battery Event Information

  • Battery Management System


The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.


Size & Weight Savings


Lithium v AGM Capacities;

  • 100Ah Lithium = 160Ah AGM

  • 125Ah Lithium = 200Ah AGM

  • 200Ah Lithium = 320Ah AGM

(Based on standard depth of discharge for both Lithium (80%) and AGM (50%).


The ePOWER B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative. The ePOWER B-TEC battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity. With over 5 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup. With over 1200 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.


Enerdrive ePOWER 24V – 30A DC2DC Battery Charger.


  • Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output

  • DC M6 screw terminals that will allow for large battery cable connection between all sources

  • A dedicated Maximum Power Point (MPPT) solar regulator

  • The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile

  • 30A output up to 40+°C with thermo controlled fan cooling

  • Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage

  • Temperature sensor included in charger for more accurate battery charging


The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays. During normal operation the ePOWER DC2DC Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.


Multistage Charging Process


The ePOWER DC2DC Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries. The ePOWER DC2DC Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery banks permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array. As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC smart charger delivers three primary charge stages.


Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible.


Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge.


Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply.


Smart Charging Feature


The ePOWER DC2DC Battery Charger will regulate its output based on the loads connected to your battery banks. This function is important to maintain the life of your battery banks as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so.

 
 

Normal Specification

EPL-100BT-24V

Nominal Voltage

25.6V

Nominal Capacity

100Ah

Cycle Life (DOD – 80% under controlled conditions)

≥ 2000 Cycles

Standard Charge Specification (Lithium profile charger required)

Battery Charge Temperature

0 ̴ 45°C

Normal Charge Voltage CV/CC*

28.80 ̴ 29.20V

Standby (Float) Voltage

27.00 ̴ 27.60V

Maximum Charge Current

50A @ 25°C for 30mins

Recommended Charge Current for Maximum Life

≤33A

Standard Discharge Specification

Battery Discharge Temperature

-20 ̴ 60°C

Battery Output Voltage Range

22.00 ̴ 29.20V

Maximum Discharge Current

100A @ 25°C ± 5°C for 30mins

Pulse Discharge Current

450A for 1.0s

Discharge Cut-off Voltage

≤22.40V

Circuit Protection

The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery.

Over-Charge Protection

Over-charge Protection Per Cell

3.90V ± 0.03V

Over-charge Release Per Cell

3.60V ± 0.05V

Over-charge Release Method

Discharge below release voltage

Over-Discharge Protection

Over-discharge Protection Per Cell

2.80V ± 0.05V

Over-discharge Release Per Cell

3.20V ± 0.05V

Over-discharge Release Method

Apply Charge/Voltage ≥25.6V

Over Current Protection

Discharge Over Current

110A for 30s – 450A for 1s

Protection Reset Time

5s Auto Release

Over Current Release Method

Disconnect Load

Over Temperature Protection

Battery Discharge Over Temperature

Protection to 65°C ± 5°C

Release at 50°C ± 5°C

Battery Charge Over Temperature

Protection to 55°C ± 5°C

Release at 45°C ± 5°C

Short Circuit Protection

Auto release after 5s

Mechanical Characteristics

Dimensions

Length 485mm

Width 170mm

Height 245mm

Weight

Approx 25.0 Kg

Storage Information

Temperature & Humidity Range

≤ 30 days -20°C ̴ 35°C, 45 ̴ 75% RH

≥ 30 days -10°C ̴ 30°C, 45 ̴ 75% RH

Self-discharge Rate

≤ 3% Per Month


Model

EN3DC30-24V

Output Rating

Output Voltage

24V Nominal (17.0V min)

Output Current (Maximum)

30A

Output Power

865W

Charger DC Output (CH1):

Selectable Battery Type

Gel, AGM, Flooded, Lithium, Program

Charger Voltage Range

27.6V – 31.0V

Float Voltage Range

26.0V – 27.6V

Charger Current (User Selectable)

5 / 10 / 20 / 30A (default 30A)

Equalize Voltage (Flooded Battery)

31.0V

Equalize Charging Current

10% of Bulk Current Setting

Charging Control

2 stage / 3 stage selectable (Default 3 Stage)

DC Output Bank

Single

Current draw from CH1 when not operating

= < 50 mA

Battery Temperature Setting

Low/ Normal/ High (Battery Temperature Sensor Standard)

Efficiency

95%

INPUT Rating (CH2 – MPPT Solar)

Input Voltage

14.5 – 45VOC

Maximum Solar Input

≤23V input, 500W (600W allowable) ≥37.5V-45V input, 800W (1000W allowable)

INPUT Rating (CH3 – Start/Alternator)

Input Voltage

10.5 – 16VDC / 21 – 32VDC

Dimensions

Height x Width x Depth

242mm x 172mm x 74mm

Unit Weight

1.85 Kg

Shipping Weight

2.17 kg

Manuals-