SMART BATTERYPROTECT 12/24V 65A

SMART BATTERYPROTECT 12/24V 65A

VICTRON SMART LOW VOLTAGE DISCONNECT • BUILT IN BLUETOOTH • PROTECTS THE BATTERY FROM OVER DISCHARGING AND CAN BE USED AS AN ISOLATOR


Brand: Victron

Reference No. BPR065022000

0

89.00Incl

80.91Excl
89.0AUD
Add to Cart

Victron smart BatteryProtect:


The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.


12/24V auto ranging:


The Smart BatteryProtect automatically detects system voltage one time only.


Bluetooth: programming made easy:


When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.


A special setting for Li-ion batteries:


In this mode the BatteryProtect can be controlled by the VE.Bus BMS.

Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.


Ultra-low current consumption:


This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.


Over voltage protection:


To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.


Ignition proof:


No relays but MOSFET switches, and therefore no sparks.


Delayed alarm output:


The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.


Delayed load disconnect and delayed reconnect:


The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.


 
 

Smart BatteryProtect

Smart BP-65

Smart BP-100

Smart BP-220

Maximum continuous load current

65A

100A

220A

Peak current (during 30 seconds)

250A

600A

600A

Operating voltage range

6 –35V

Current consumption

BLE On

When on: 1,4 mA When off or low voltage shutdown : 0,9 mA

BLE Off

When on: 1,2 mA When off or low voltage shutdown : 0,7 mA

Alarm output delay

12 seconds

Maximum load on alarm output

50 mA (short circuit proof)

Load disconnect delay

90 seconds (immediate if triggered by the VE.Bus BMS)

Load reconnect delay

30 seconds

Default thresholds

Disengage: 10,5V or 21V Engage: 12V or 24V

Operating temperature range

Full load: -40°C to +40°C (up to 60% of nominal load at 50°C)

Connection

M6

M8

M8

Weight

0,2 kg 0.5 lbs

0,5 kg 0.6 lbs

0,8 kg 1.8 lbs

Dimensions (HxWxD)

40x48x106mm

1.6 x 1.9 x 4.2inch

59x42x115mm

2.4 x 1.7 x 4.6inch

62x123x120mm

2.5 x 4.9 x 4.8inch

 

Victron smart Batteryprotect 12/24V 65A spec Sheet-


Victron smart Batteryprotect 12/24V 65A manual-


Victron smart Batteryprotect 12/24V 65A dimensions-